10mm LeD Haske Green LED tare da share lens

10mm kore led fitila fitilar haske mai haske tare da ruwan tabarau bayyananne

Kamar yadda muka sani, akwai da irin siffar da kuma size for Ta-rami LED fitilu, kamar murabba'i mai dari, zagaye saman, lebur saman ect. Kuma don girman, 3mm, 5mm, 8mm har ma da girman 10mm da aka samu. A cikin wannan 1004LGC-12, muna samar da shi tare da 10mm kore share epoxy a waje kamar yadda ake. Da wannan yanayin kore a bayyane, wannan 100mm kore ta hanyar-rami ya sami damar fitar da haske da launi kamar yadda ya kamata. Bugu da kari, muna iya san menene launinsa lokacin da wannan karamin farashin kwan fitila ba sa haske.

Wannan 10mm Leed Hammalall za a yi amfani da shi don fitarwa kamar yadda kwan fitila da aka lallasa da yawa. Don tabbatar da cewa yana iya samun cikakken aiki, muna samar da shi tare da babban shahararren shahararrun alama Chip ciki kuma an sami ƙarin aiki har ma da aiki mai zuwa. Hasken zai iya isa 20000-300mCd lokacin da kuka wuce na yanzu zuwa gare ta. Idan kuna buƙatar fitilar fitila mai haske don aikinku kuma yana buƙatar wannan tare da girman 10mm, wannan ba zai bari ku ji daɗin rashin jin daɗi ~

Girman kore ta hanyar-rami ya jagoranci

Zabin lantarki:

* Purse gaba yanayin halin yanzu: Hadince 1% da kuma girman kai = 10USU.

* Yanayin Siyayya: Dole ne a kammala yanayin Siyarwa tare da 3 Secondds a 260 ℃

Enletrucal Entical halaye (TC = 25 ℃ )

* Ana auna ƙarfin haske da ZWL600.

* θ1 / 2 shine kashe-sxis na sxis wanda mai tsananin zafi shine rabin mafi girman haske;

Aikace-aikacen kore 520nm led:

Mai nuna alama;

Tsarin LED Haske;

LED DIY Aikin;

Yanayin ajiya:

1. Guji cigaba da bayyanar da yanayin danshi da kuma kiyaye samfurin daga saurin canzawa a cikin zafin jiki;

2. LEDs ya kamata a adana tare da zafin jiki ≤30 ℃ da dangi zafi ℃ 60% ℃;

3. Samfurin a cikin Kunshin da aka rufe da aka rufe da aka wanke an ba da shawarar haɗuwa cikin sa'o'i 72 na buɗewa;

4. Samfurin a bude fakiti fiye da sati fiye da sati ya kamata a gasa tsawon 6-8 hours a 85-10 ℃;

Hanyar hawa hawa

1, jagorar farar fata na led dole ne ya dace da farar rami a kan PCB yayin bangarori;

Ana buƙatar buƙatar ƙirƙirar tsari don inshorar filin wasan da ya dace da farar rami;

Koma zuwa adadi da ke ƙasa don ingantaccen tsarin tsara tsari;

Kada ku shiga PCB alama a cikin lambar sadarwa tsakanin jigon da kuma PCB don hana gajerun da'irori;

Lura:

○ Hanyar hawa;

Hanyar hawa ba daidai ba;

2. A lokacin da aka sayar da wayoyi zuwa ga LED, kowane haɗin haɗin gwiwa ya kamata ya zama wanda ke tattare da bututun-shamaki don hana gajeriyar lamba.

Kada ku haɗa wayoyi a cikin bututun ruwa ɗaya don guje wa tsaftace jagorar;

Pinching damuwa a kan LED Shiga na iya lalata tsarin ciki kuma yana haifar da rashin nasara;

Lura:

○ Hanyar hawa;

Hanyar hawa ba daidai ba;

3. Yi amfani da tsayawa (Fig 3) ko Sprers (Fig 4) don amintaccen wuri wanda ya jagorantar PCB;

4. Kula da mafi karancin tsallake na 3mm tsakanin gindin ruwan tabarau na LED da na farko (Fig. 6)

5. A lokacin jagoranci tsari, amfani da kayan aiki ko Jigs don riƙe jagorancin amintacce don ba za a watsa ƙarfin ƙarfin ruwan tabarau na LED da tsarin ciki;

Kada ku yi tsari na jagorancin da zarar an sanya bangaren akan PCB;

L ead forming tsari

1. Jagoran hanyoyin aiwatar da tsari;

2. Kada ka tanƙwara kan gaba fiye da sau biyu (Fig. 7);

3. A lokacin sojoji, kayan haɗin gwiwa da masu riƙe suna barin yarda don gujewa kawar da daming danniya a yayin sayar da (Fig 8);

4. Thearshen baƙin ƙarfe ya kamata ba zai taɓa taɓa ruwan tabarau ba;

5. By-rami Leds bai dace da Schall Sanga ba;

6. Idan LED za ta sha da yawa na sayar da yawa na wucewa ko fuskantar wasu matakai inda ɓangaren na iya yin zafi zuwa matsanancin zafi don Allah a bincika mafi kyawun LED don dacewa;