Far Red LED 1450nm 5mm IR LED

Far Red IR LED tare da 1450nm LED

Za mu iya samar da guntu na LED iri ɗaya tare da hanyar pakcage daban-daban, kamar nau'in LED na SMD ko nau'in Lambobin LED na rami. A cikin wannan samfurin, muna samar da wannan 504FIRBT-150L14I100 a cikin 5mm ta cikin ramin LED. Wannan shine IR LED, amma raƙuman raƙuman ruwa ba madaidaicin raƙuman ruwa ba ne kuma yana da girma sosai, mu ma muna kiran waɗancan 1550nm LED, 1300nm LED ko 1050nm LED har zuwa ja LED.

Kwatanta da smd led IR LED, kamar nau'in 2835 SMD LED. Za mu sami ƙarin raditaion nesa daga wannan fakitin LED na 5mm fiye da nau'in LED na 2835 SMD. Idan kuna buƙatar wannan 1450nm LED don fitar da nesa mai nisa to don Allah ku tafi tare da nau'in LED mai rami. Amma idan kuna buƙatar wannan IR LED don fitar da yanki mai faɗi don aikin ku, don Allah ku tafi tare da nau'in LED na SMD.

Yanayin ajiya:

1. Guji cigaba da bayyanar da yanayin danshi da kuma kiyaye samfurin daga saurin canzawa a cikin zafin jiki;

2. LEDs ya kamata a adana tare da zafin jiki ≤30 ℃ da dangi zafi ℃ 60% ℃;

3. Samfurin a cikin Kunshin da aka rufe da aka rufe da aka wanke an ba da shawarar haɗuwa cikin sa'o'i 72 na buɗewa;

4. Samfurin a bude fakiti fiye da sati fiye da sati ya kamata a gasa tsawon 6-8 hours a 85-10 ℃;

Hanyar hawa hawa

1, jagorar farar fata na led dole ne ya dace da farar rami a kan PCB yayin bangarori;

Ana buƙatar buƙatar ƙirƙirar tsari don inshorar filin wasan da ya dace da farar rami;

Koma zuwa adadi da ke ƙasa don ingantaccen tsarin tsara tsari;

Kada ku shiga PCB alama a cikin lambar sadarwa tsakanin jigon da kuma PCB don hana gajerun da'irori;

Lura:

○ Hanyar hawa;

Hanyar hawa ba daidai ba;

2. A lokacin da aka sayar da wayoyi zuwa ga LED, kowane haɗin haɗin gwiwa ya kamata ya zama wanda ke tattare da bututun-shamaki don hana gajeriyar lamba.

Kada ku haɗa wayoyi a cikin bututun ruwa ɗaya don guje wa tsaftace jagorar;

Pinching damuwa a kan LED Shiga na iya lalata tsarin ciki kuma yana haifar da rashin nasara;

Lura:

○ Hanyar hawa;

Hanyar hawa ba daidai ba;

3. Yi amfani da tsayawa (Fig 3) ko Sprers (Fig 4) don amintaccen wuri wanda ya jagorantar PCB;

4. Kula da mafi karancin tsallake na 3mm tsakanin gindin ruwan tabarau na LED da na farko (Fig. 6)

5. A lokacin jagoranci tsari, amfani da kayan aiki ko Jigs don riƙe jagorancin amintacce don ba za a watsa ƙarfin ƙarfin ruwan tabarau na LED da tsarin ciki;

Kada ku yi tsari na jagorancin da zarar an sanya bangaren akan PCB;

L ead forming tsari

1. Jagoran hanyoyin aiwatar da tsari;

2. Kada ka tanƙwara kan gaba fiye da sau biyu (Fig. 7);

3. A lokacin sojoji, kayan haɗin gwiwa da masu riƙe suna barin yarda don gujewa kawar da daming danniya a yayin sayar da (Fig 8);

4. Thearshen baƙin ƙarfe ya kamata ba zai taɓa taɓa ruwan tabarau ba;

5. By-rami Leds bai dace da Schall Sanga ba;

6. Idan LED za ta sha da yawa na sayar da yawa na wucewa ko fuskantar wasu matakai inda ɓangaren na iya yin zafi zuwa matsanancin zafi don Allah a bincika mafi kyawun LED don dacewa;